저자명 Waseem Gul 
년도 2010 
A stiffened plate is regarded as an assembly of the plating, due to simplicity in fabrication and the excellent strength to the weight ratio, stiffened plates are frequently used as structural components in ships and offshore structures. In all such application, it is always a paramount for structural designer/analyst to determine actual load carrying capacity of the structure.
In the present study, the ultimate strength of stiffened plates subjected to predominately axial compression is evaluated using Non-linear finite element analysis. Parametric studies covering a wide range of dimensionless parameters are carried out. The Parameters investigated are: the transverse flexural slenderness of the plate, the stiffener web slenderness, stiffener flange slenderness, and plate aspect ratio. From the parametric study, it is found that transverse flexure slenderness of the stiffened plate is more influential parameter as compared to other dimensionless parameter. It is observed that ultimate buckling strength decreases as the value of plate transverse flexure slenderness increases. Failure mode is also changed from plate induced overall bucking to plate buckling with increase in plate transverse flexural slenderness, which results in increasingly unstable post buckling behavior.
Strain hardening effect is evaluated and it is found that, strain hardening yields higher ultimate buckling strength. Ignoring the strain hardening effect, as it is common practice in marine industry, may cause underestimation of steel plated structure.
It is the matter of fact that thick hot rolled plate shows variation in material properties along the thickness direction. Effects of this phenomenon on ultimate buckling strength of stiffened plate are investigated and found to be significant. Furthermore, combined effect of strain hardening and variation in material properties along the thickness direction, yield remarkable increase in ultimate buckling strength of the stiffened plates. Therefore, in order to evaluate the ultimate buckling strength of stiffened plate accurately, variation in material properties along the thickness direction must be considered in the design and analysis of marine stiffened plates.
Effects of fabrication related imperfection are evaluated and it is found that imperfections have severe effects on the ultimate buckling strength of stiffened plate. Even at certain value of imperfection stiffened plate buckle before reaching to its yield strength. It is also found that as the plate flexural slenderness is increasing imperfection effect becomes more dominant and post buckling response also become sharply unstable.
A comparison of the numerical analysis results with design guidelines formulated by Det norske Veritas (DnV) and the American Petroleum Institute (API) is made. This comparison indicates that, in case of plate induced overall buckling, the guidelines results have good agreement with numerical results.
번호 제목 저자명 날짜 조회 수
49 Structural Design and Evaluation for Improvement of the Roof Strength of a Three-Wheel Vehicle(삼륜차의 루프 강도 향상을 위한 구조 설계 및 평가) file Jesung Yoo  2017.06.07 107
48 Tension/Compression Hardening Behavior of Auto-body Steel Sheets at Intermediate Strain Rates Ranging from 0.1/s to 50/s(중 변형률속도 0.1/s ~ 50/s 영역에서의 차체 강판의 인장/압축 경화 거동에 관한 연구) 주근수  2014.01.16 3343
47 Tensile Properties of Nugget Region in a Spot Weld at Various Strain-Rates (점용접 너겟부의 변형률속도에 따른 인장 물성에 관한 연구) 박문수  2014.01.16 3012
46 Validation of Dynamic Hardening Models at High Strain Rates Using Taylor Impact Tests (테일러 충격시험을 이용한 고 변형률속도 조건에서의 동적 경화모델 검증) 박명준  2013.09.02 3894
45 Tensile Material Properties of Carbon/epoxy Composite Laminates at High Strain Rates (탄소섬유강화 복합재료의 변형률 속도에 따른 인장물성의 평가) 최재영  2013.02.12 6078
44 Design and Dynamic Simulation of a New Shock Absorbing Device with a Bending Strap in a Helicopter Pilot Seat (헬리콥터 조종석의 굽힘 판재를 이용한 새로운 충격흡수장치의 설계 및 동적 모사해석에 관한 연구) [1] 박주형  2013.02.12 6231
43 Anisotropy Effect on the Fracture Forming Limit Diagram of DP980 Sheets Considering the Loading Path (DP980 강판의 하중경로를 고려한 파단성형한계도에 미치는 이방성의 영향) 박남수  2013.02.12 5304
42 Study on the Dynamic Failure Model of Structural Adhesive Joints under Combined Loading Conditions(차량 구조용 접착제를 이용한 접합부의 복합하중조건에서 동적 파단 특성 연구) 임승찬  2013.01.24 4718
41 Study on the Strain-Rate Dependent Tensile Properties of Micro-Scale Aluminum Specimens(알루미늄 마이크로시편의 변형률속도에 따른 인장 특성 연구) 권준범  2012.03.01 7021
40 Study on the Fracture Strain of DP780 Sheets Considering the Strain Rate and Loading Path (변형률속도와 하중경로를 고려한 DP780 강재의 파단변형률에 관한 연구) 박근환  2012.02.20 10738
» Evaluation of Ultimate Buckling Strength of Stiffened Plates for Marine Structures (해양구조물용 보강판구조의 좌굴한계강도 평가) Waseem Gul  2010.07.13 7699
38 Study on Design of Stress Wave Micro Sensor for High Speed Transportation Safety System (고속운송기구의 안전시스템을 위한 마이크로 응력파 센서 설계 연구) 임성준  2010.07.13 6536
37 Study on the Anisotropy of Auto-body Steel Sheets considering the Strain Rate(변형률속도를 고려한 차체강판의 이방성에 관한 연구) 이창수  2010.07.13 7940
36 Reliability Based Design Optimization for Crashworthiness of a Spot Welded Hat Type Member (점용접 모자형 사각관의 충돌성능에 대한 신뢰도 기반 최적설계) 김유종  2010.07.13 6298
35 Upper Bound Analysis of Dynamic Buckling Phenomenon of Circular Tubes Considering Strain Rate Effect (변형률 속도를 고려한 원형 튜브의 동적 좌굴 현상의 상계 해석에 관한 연구) 박충희  2008.08.02 6097
34 Study on the Crash Energy Absorption and Dynamic Local Buckling of the Expansion Tubes (확관튜브의 충돌에너지 흡수성능 및 동적 국부좌굴에 관한 연구) 안광현  2008.01.28 5387
33 Dynamic Material Properties of the Heat-Affected Zone (HAZ) in a Resistance Spot Weld(점용접 열영향부의 동적 물성특성에 관한 연구) 하지웅  2008.01.25 6866
32 Cross-section Shape Design of an Aluminum Crash Box for Crashworthiness Enhancement (충돌성능 향상을 위한 알루미늄 크래쉬 박스의 단면 형상 설계) [1] 이경호  2008.01.25 6458
31 Finite Element Inverse Analysis of the Sheet Metal Forming Process Considering Bending History (굽힘 이력을 고려한 박판성형공정의 유한요소 역해석) 허지향  2008.01.25 5203
30 Study on the 3-D finite element modeling of fiber reinforced rubber composite using the rebar element (리바요소를 이용한 섬유강화 고무기저 복합재료의 3차원 유한요소 모델링기법 연구) 정세환  2006.08.18 5857