저자명 권준범 
년도 2012 

The material properties of A1100 film with a thickness of 96 µm has been evaluated at strain rates ranging from 0.001/s to 100/s using Static Micro Material Testing Machine (SMMTM) and High-Speed Micro Material Testing Machine (HSMMTM). The high strain-rate material properties of thin films are important especially for the evaluation of structural reliability of micro-formed parts and micro-electromechanical systems (MEMS) products. The high strain-rate material testing methods of thin films, however, are not yet thoroughly established, while testing methods of larger specimens for electronics, auto-body, and ocean structures has been well-established.

 In the present study, a Micro-tester has been newly developed for micro-tensile tests at strain rates ranging from 0.001/sec to 0.1/sec. The new machine has a gearhead type linear motor and an accurate load measurement system. The gearhead type linear motor has the maximum tensile load of 70 N and the maximum tensile speed of 1.5 mm/s. Also, a new jig system for HSMMTM has been newly developed for easy installation of a specimen and accurate alignment between a specimen and the jig system to enhance the reproducibility of tests. Digital image correlation (DIC) method is employed to measure the axial strain of micro-specimens. To enhance the accuracy of the strain measurement, a novel technique is introduced such that very fine speckle patterns can be made. For A1100 thin film with the thickness of 96 µm, micro-tensile tests have been performed using Micro-tester  at strain rates from 0.001/s to 0.1/s, and using HSMMTM at strain rates from 1/s to 100/s. The dimension of a specimen is 300 µm in gauge width and 1500 µm in gauge length, which were fabricated by micro-photo etching technique.

  To examine the effect of grain size and specimen size on the tensile properties of A1100, the tensile tests have been carried out at the strain rates ranging from 0.001/s to 100/s using Instron5583 and high speed material testing machine (HSMTM) for A1100 with the thickness of 1.0 mm. Electron Back Scattered Diffraction(EBSD) and Focused Ion Beam(FIB) images were obtained for both micro and macro specimens and analyzed to measure the grain size. The grain size of two A1100 has been compared and the number of grains in the gauge cross-section has been evaluated. The A1100 film with smaller average grain size shows larger strain hardening than the A1100 sheet with larger average grain size. The flow stress of the A1100 film with smaller grains was higher than the A1100 sheet with larger grains. This result shows the opposite result with those of OFHC copper film.

번호 제목 저자명 날짜 조회 수
49 Structural Design and Evaluation for Improvement of the Roof Strength of a Three-Wheel Vehicle(삼륜차의 루프 강도 향상을 위한 구조 설계 및 평가) file Jesung Yoo  2017.06.07 157
48 Tension/Compression Hardening Behavior of Auto-body Steel Sheets at Intermediate Strain Rates Ranging from 0.1/s to 50/s(중 변형률속도 0.1/s ~ 50/s 영역에서의 차체 강판의 인장/압축 경화 거동에 관한 연구) 주근수  2014.01.16 3405
47 Tensile Properties of Nugget Region in a Spot Weld at Various Strain-Rates (점용접 너겟부의 변형률속도에 따른 인장 물성에 관한 연구) 박문수  2014.01.16 3065
46 Validation of Dynamic Hardening Models at High Strain Rates Using Taylor Impact Tests (테일러 충격시험을 이용한 고 변형률속도 조건에서의 동적 경화모델 검증) 박명준  2013.09.02 3962
45 Tensile Material Properties of Carbon/epoxy Composite Laminates at High Strain Rates (탄소섬유강화 복합재료의 변형률 속도에 따른 인장물성의 평가) 최재영  2013.02.12 6140
44 Design and Dynamic Simulation of a New Shock Absorbing Device with a Bending Strap in a Helicopter Pilot Seat (헬리콥터 조종석의 굽힘 판재를 이용한 새로운 충격흡수장치의 설계 및 동적 모사해석에 관한 연구) [1] 박주형  2013.02.12 6288
43 Anisotropy Effect on the Fracture Forming Limit Diagram of DP980 Sheets Considering the Loading Path (DP980 강판의 하중경로를 고려한 파단성형한계도에 미치는 이방성의 영향) 박남수  2013.02.12 5363
42 Study on the Dynamic Failure Model of Structural Adhesive Joints under Combined Loading Conditions(차량 구조용 접착제를 이용한 접합부의 복합하중조건에서 동적 파단 특성 연구) 임승찬  2013.01.24 4778
» Study on the Strain-Rate Dependent Tensile Properties of Micro-Scale Aluminum Specimens(알루미늄 마이크로시편의 변형률속도에 따른 인장 특성 연구) 권준범  2012.03.01 7075
40 Study on the Fracture Strain of DP780 Sheets Considering the Strain Rate and Loading Path (변형률속도와 하중경로를 고려한 DP780 강재의 파단변형률에 관한 연구) 박근환  2012.02.20 10815
39 Evaluation of Ultimate Buckling Strength of Stiffened Plates for Marine Structures (해양구조물용 보강판구조의 좌굴한계강도 평가) Waseem Gul  2010.07.13 7759
38 Study on Design of Stress Wave Micro Sensor for High Speed Transportation Safety System (고속운송기구의 안전시스템을 위한 마이크로 응력파 센서 설계 연구) 임성준  2010.07.13 6596
37 Study on the Anisotropy of Auto-body Steel Sheets considering the Strain Rate(변형률속도를 고려한 차체강판의 이방성에 관한 연구) 이창수  2010.07.13 7995
36 Reliability Based Design Optimization for Crashworthiness of a Spot Welded Hat Type Member (점용접 모자형 사각관의 충돌성능에 대한 신뢰도 기반 최적설계) 김유종  2010.07.13 6354
35 Upper Bound Analysis of Dynamic Buckling Phenomenon of Circular Tubes Considering Strain Rate Effect (변형률 속도를 고려한 원형 튜브의 동적 좌굴 현상의 상계 해석에 관한 연구) 박충희  2008.08.02 6155
34 Study on the Crash Energy Absorption and Dynamic Local Buckling of the Expansion Tubes (확관튜브의 충돌에너지 흡수성능 및 동적 국부좌굴에 관한 연구) 안광현  2008.01.28 5458
33 Dynamic Material Properties of the Heat-Affected Zone (HAZ) in a Resistance Spot Weld(점용접 열영향부의 동적 물성특성에 관한 연구) 하지웅  2008.01.25 6932
32 Cross-section Shape Design of an Aluminum Crash Box for Crashworthiness Enhancement (충돌성능 향상을 위한 알루미늄 크래쉬 박스의 단면 형상 설계) [1] 이경호  2008.01.25 6511
31 Finite Element Inverse Analysis of the Sheet Metal Forming Process Considering Bending History (굽힘 이력을 고려한 박판성형공정의 유한요소 역해석) 허지향  2008.01.25 5253
30 Study on the 3-D finite element modeling of fiber reinforced rubber composite using the rebar element (리바요소를 이용한 섬유강화 고무기저 복합재료의 3차원 유한요소 모델링기법 연구) 정세환  2006.08.18 5917