저자명 김세호 
년도 1995 
The sheet metal forming process is accompanied by the large amount of deformation and rotation which causes springback after unloading. To calculate the amount of springback, the proper evaluation of stress components should be achieved in finite element simulation. In an elasto-plastic finite element analysis, the stress components in each incremental step is evaluated and employed to construct the stiffness matrix of the next step. Therefore, accurate stress calculation in the finite element analysis is very important. In this study, an elasto-plastic finite element analysis is carried out using 4-node iso-parametric element and accuracy of stress calculation at each integration point in each incremental step is examined. When the directional reduced integration or the full integration scheme is adopted, the proper evaluation of stress components at each integration point cannot be achieved. To obtain accurate stress values at integration points, a reduced integration scheme is adopted with the treatment of the hourglass modes which arise due to reduced integration. The hourglass modes can be controlled by an assumed strain method. The finite element program developed using a reduced integration scheme is applied to a class of plane strain problems such as tension of a tapered specimen and bending of a simply supported beam. The numerical result demonstrates the deviation of stress values calculated by a DRI or FI scheme from that by a RI scheme. The application also studies the effect of the aspect ratio of an element and the number of layers in the thickness direction on the calculated solutions.

번호 제목 저자명 날짜 조회 수
49 Structural Design and Evaluation for Improvement of the Roof Strength of a Three-Wheel Vehicle(삼륜차의 루프 강도 향상을 위한 구조 설계 및 평가) file Jesung Yoo  2017.06.07 1523
48 Elasto-plastic finite element method with directional reduced integration in sheet metal forming( 선향적 저감 적분을 이용한 탄소성 유한 요소법에 의한 박판성형해석 ) 한수식  2005.11.29 3743
47 Numerical simulation of bead formation by an elasto-plastic finite element method (탄소성 유한요소법을 이용한 비드 성형의 수치해석) 천병관  2005.11.29 3749
46 Effective experimental method for identification of the forming limit diagram of sheet metals (금속 박판의 성형한계도를 구하기 위한 실험방법 개선에 관한 연구) 정제웅  2005.11.29 4005
45 Finite element simulation of superplastic sheet forming with initial non-uniform thickness distribution (초기 두께분포가 있는 초소성 재료의 유한요소 성형해석) 최영준  2005.11.29 4087
44 Self contact analysis of rubber-boots for C. V. joints by a 3-D finite element method (3차원 유한요소법을 이용한 등속조인트 고무 부트의 자체접촉해석) 이형욱  2005.11.29 4325
43 Three-dimensional Finite Element Analysis of Air Springs with Fiber-reinforced Rubber Composites (섬유강화 고무복합재 공기스프링의 3차원 유한요소 해석) 신진원  2005.11.29 4374
42 Numerical simulations of sheet forming processes by an elasto-plastic finite element method (탄소성 유한요소법을 이용한 박판 성형 공정 해석) [1] 최태훈  2005.11.29 4385
41 Plastic collapse analysis of hollow pipe structures by finite element limit analysis (유한요소 극한해석을 이용한 중공 파이프 구조물의 소성 붕괴 거동 해석 ) 서종관  2005.11.29 4390
40 Tensile Properties of Nugget Region in a Spot Weld at Various Strain-Rates (점용접 너겟부의 변형률속도에 따른 인장 물성에 관한 연구) 박문수  2014.01.16 4431
39 Design of process parameters in axisymmetric multi-step deep drawing by a finite element inverse method (유한요소 역 해석을 이용한 축대칭 다단계 박판성형에서의 공정변수 설계에 관한 연구) 조천수  2005.11.29 4456
38 Experiment and Finite Element Analysis of the Formation of Adiabatic Shear Band in Sheet Metal (박판금속의 단열전단밴드 생성에 대한 실험 및 유한요소 해석) 임지호  2005.11.29 4516
37 Tension Test and Specimen Design with the Finite Element Method at Intermediate Strain Rates(준고속 변형률 속도에서의 인장실험 및 유한요소법을 이용한 박판 인장시편의 형상결정) 송정한  2005.11.29 4648
36 Adaptive Time-stepping Procedure for Dynamic Limit Analysis (동적 극한해석을 위한 적응적 시간간격기법) 이종섭  2005.11.29 4652
35 Tension/Compression Hardening Behavior of Auto-body Steel Sheets at Intermediate Strain Rates Ranging from 0.1/s to 50/s(중 변형률속도 0.1/s ~ 50/s 영역에서의 차체 강판의 인장/압축 경화 거동에 관한 연구) 주근수  2014.01.16 4678
34 Preform Design for Net Shape Sinter-forging of Powdered Magnets with Curved Shape (곡면 형상을 가지는 분말 자석의 정형 가공을 위한 예비성형체의 설계) 김승호  2005.11.29 4688
33 Efficiency enhancement of sheet metal forming analysis with a mesh regularization method (격자 정방형화 방법을 이용한 박판 성형해석의 효율개선) 윤종헌  2005.11.29 4785
32 Validation of Dynamic Hardening Models at High Strain Rates Using Taylor Impact Tests (테일러 충격시험을 이용한 고 변형률속도 조건에서의 동적 경화모델 검증) 박명준  2013.09.02 5137
31 Electrothermal analysis of large electric current systems by finite element method (유한요소법을 이용한 대전류 시스템의 전열해석 ) 강우종  2005.11.29 5268
30 Study on the characterization of the dynamic material properties of sheet metal for auto-body considering the pre-strain effect(예비변형률 효과를 고려한 차체용 박판의 동적 물성 특성 연구) 김석봉  2005.11.29 5282