저자명 박근환 
년도 2012 



Fracture strain data in proportional loading conditions are essential to develop and construct ductile fracture models which can predict onset of fracture in metals accurately. To evaluate the possibility of fracture in real forming processes, the strain rate effect should also be taken into account. In the present work, the hybrid experimentalnumerical method and the 2-dimensional digital image correlation (2D-DIC) method are introduced to measure the fracture strain of DP780 sheets in the wide range of the loading path in terms of the stress triaxiality and the Lode angle, and in the intermediate strain rates.

Firstly, uniaxial tensile tests are carried out in the rolling, transverse, and diagonal directions in order to measure r-values and construct the yield function which will be used for finite element analysis. To obtain hardening curves with strain rates, uniaxial tensile tests in the rolling direction are conducted for six strain rates from 0.001/s to 100/s.

Four types of specimen shapes are chosen to induce various loading paths to the material point where the maximum equivalent plastic strain is observed under uniaxial tensile loading. For the pure shear condition, a diagonally double notched specimen is slightly modified. A specimen with a central hole is used for the uniaxial tension condition along with a dog bone specimen because its loading path is kept nearly constant through the entire deformation process in spite of necking. Plane strain tension condition is achieved by a flat grooved specimen. The fourth type has two symmetric cutouts which can control the initial loading path. The cross-head speed of each test is determined such that the average strain rate of the fracture initiation point reaches the target strain rate. The loading histories of each type of a specimen are thoroughly investigated with finite element analysis and average loading paths are calculated.

Fracture tests are carried out using INSTRON 5583 and high speed material testing machine with deformation images captured by the high speed camera. For the quasi-static case, both the hybrid experimental-numerical method and the 2D-DIC method are employed in order to measure the fracture strain. By comparing 3D fracture surfaces and 2D fracture loci constructed based on the measured data with each method, applicability of the 2D-DIC method to measuring the fracture strain of DP780 sheets are explored. Thus, for higher strain rates, only is the DIC method adopted to measure the fracture strain because reliable true stresstrue strain curves beyond necking at various strain rates are difficult to determine.

Based on the acquired fracture strain data and calculated average loading paths, the modified MohrCoulomb fracture loci are constructed and represented with respect to the strain rate. Also, the loci are transformed into fracture forming limit diagrams which is relatively easy to understand and compare with conventional forming limit diagrams.


번호 제목 저자명 날짜 조회 수
49 Structural Design and Evaluation for Improvement of the Roof Strength of a Three-Wheel Vehicle(삼륜차의 루프 강도 향상을 위한 구조 설계 및 평가) file Jesung Yoo  2017.06.07 1333
48 Tension/Compression Hardening Behavior of Auto-body Steel Sheets at Intermediate Strain Rates Ranging from 0.1/s to 50/s(중 변형률속도 0.1/s ~ 50/s 영역에서의 차체 강판의 인장/압축 경화 거동에 관한 연구) 주근수  2014.01.16 4516
47 Tensile Properties of Nugget Region in a Spot Weld at Various Strain-Rates (점용접 너겟부의 변형률속도에 따른 인장 물성에 관한 연구) 박문수  2014.01.16 4262
46 Validation of Dynamic Hardening Models at High Strain Rates Using Taylor Impact Tests (테일러 충격시험을 이용한 고 변형률속도 조건에서의 동적 경화모델 검증) 박명준  2013.09.02 4967
45 Tensile Material Properties of Carbon/epoxy Composite Laminates at High Strain Rates (탄소섬유강화 복합재료의 변형률 속도에 따른 인장물성의 평가) 최재영  2013.02.12 7449
44 Design and Dynamic Simulation of a New Shock Absorbing Device with a Bending Strap in a Helicopter Pilot Seat (헬리콥터 조종석의 굽힘 판재를 이용한 새로운 충격흡수장치의 설계 및 동적 모사해석에 관한 연구) [1] 박주형  2013.02.12 8078
43 Anisotropy Effect on the Fracture Forming Limit Diagram of DP980 Sheets Considering the Loading Path (DP980 강판의 하중경로를 고려한 파단성형한계도에 미치는 이방성의 영향) 박남수  2013.02.12 6869
42 Study on the Dynamic Failure Model of Structural Adhesive Joints under Combined Loading Conditions(차량 구조용 접착제를 이용한 접합부의 복합하중조건에서 동적 파단 특성 연구) 임승찬  2013.01.24 5860
41 Study on the Strain-Rate Dependent Tensile Properties of Micro-Scale Aluminum Specimens(알루미늄 마이크로시편의 변형률속도에 따른 인장 특성 연구) 권준범  2012.03.01 8147
» Study on the Fracture Strain of DP780 Sheets Considering the Strain Rate and Loading Path (변형률속도와 하중경로를 고려한 DP780 강재의 파단변형률에 관한 연구) 박근환  2012.02.20 11968
39 Evaluation of Ultimate Buckling Strength of Stiffened Plates for Marine Structures (해양구조물용 보강판구조의 좌굴한계강도 평가) Waseem Gul  2010.07.13 8853
38 Study on Design of Stress Wave Micro Sensor for High Speed Transportation Safety System (고속운송기구의 안전시스템을 위한 마이크로 응력파 센서 설계 연구) 임성준  2010.07.13 7841
37 Study on the Anisotropy of Auto-body Steel Sheets considering the Strain Rate(변형률속도를 고려한 차체강판의 이방성에 관한 연구) 이창수  2010.07.13 9090
36 Reliability Based Design Optimization for Crashworthiness of a Spot Welded Hat Type Member (점용접 모자형 사각관의 충돌성능에 대한 신뢰도 기반 최적설계) 김유종  2010.07.13 7404
35 Upper Bound Analysis of Dynamic Buckling Phenomenon of Circular Tubes Considering Strain Rate Effect (변형률 속도를 고려한 원형 튜브의 동적 좌굴 현상의 상계 해석에 관한 연구) 박충희  2008.08.02 7333
34 Study on the Crash Energy Absorption and Dynamic Local Buckling of the Expansion Tubes (확관튜브의 충돌에너지 흡수성능 및 동적 국부좌굴에 관한 연구) 안광현  2008.01.28 6522
33 Dynamic Material Properties of the Heat-Affected Zone (HAZ) in a Resistance Spot Weld(점용접 열영향부의 동적 물성특성에 관한 연구) 하지웅  2008.01.25 7938
32 Cross-section Shape Design of an Aluminum Crash Box for Crashworthiness Enhancement (충돌성능 향상을 위한 알루미늄 크래쉬 박스의 단면 형상 설계) [1] 이경호  2008.01.25 8142
31 Finite Element Inverse Analysis of the Sheet Metal Forming Process Considering Bending History (굽힘 이력을 고려한 박판성형공정의 유한요소 역해석) 허지향  2008.01.25 6224
30 Study on the 3-D finite element modeling of fiber reinforced rubber composite using the rebar element (리바요소를 이용한 섬유강화 고무기저 복합재료의 3차원 유한요소 모델링기법 연구) 정세환  2006.08.18 7028